Difference between revisions of "MIA electric"

From wiki.bastelbude.grade.de
Jump to: navigation, search
(DC charging)
(sandbox)
 
(19 intermediate revisions by the same user not shown)
Line 1: Line 1:
 
== sandbox ==
 
== sandbox ==
 +
=== CAN-bus sniffing ===
 +
* parts
 +
** Arduino UNO R3 (or CH340 clone EUR 6,49)
 +
** MCP2515 / TJA1050 shield http://blog.dimitarmk.com/wp-content/uploads/2016/12/wiringarduinomcp2515.png (8MHz EUR 4,79)
 +
** https://github.com/latonita/arduino-canbus-monitor (MCP_8MHz, CAN_500KBPS)
 +
** OBD-II connector: Pin-6=CAN-high / Pin-14=CAN-low  EUR 1,69
 +
** CANcool https://github.com/MHS-Elektronik/CANcool
 +
 +
=== socketcand ('can over tcp/ip') ===
 +
* prerequisites:
 +
** Linux maschine
 +
** Arduino + CANbus shield + SLCAN ( https://github.com/latonita/arduino-canbus-monitor )
 +
* setup:
 +
** install can-utils <pre>sudo apt-get install can-utils</pre>
 +
** install socketcand http://kayak.2codeornot2code.org/tutorial.html
 +
* run:
 +
:<pre>slcand -o -s6 -t hw 115200 /dev/ttyusb0</pre>
 +
:<pre>ip link set up slcan0</pre>
 +
:<pre>socketcand -i slcan0</pre>
 +
* usage:
 +
** http://kayak.2codeornot2code.org/
 +
 +
=== CANcool ===
 +
* [http://www.mhs-elektronik.de/index.php?module=content&action=show&page=can_cool website]
 +
* [https://www.mikrocontroller.net/topic/283166 forum]
 +
* [https://github.com/MHS-Elektronik/CANcool sources]
 +
==== 'Berechnungs-Term' ====
 +
* operators:
 +
+  // addition
 +
-  // subtraction
 +
*  // multiplication
 +
/  // division
 +
<< // Bit shift left
 +
>> // Bit shift right
 +
&  // AND
 +
|  // OR
 +
~  // XOR
 +
* variables:
 +
d0 1st byte (decimal)
 +
d1 2nd byte (decimal)
 +
d3 3rd byte (decimal)
 +
d4 ...
 +
d5 ...
 +
d6 ...
 +
d7 ...
 +
* samples:
 +
d0                                                                // unsigned char (8-bit)
 +
(d0 - ((d0 >> 7)*256))                                            // signed char (8-bit) Two's complement
 +
((d0 << 8) + d1) ^= MSB * 256 + LSB                                // unsigned short (16-bit)
 +
(((d0 << 8) + d1) - ((d0 >> 7)*65536))                            // signed short (16-bit) Two's complement
 +
((d0 << 24) + (d1 << 16) + (d2 << 8) + d3)                        // unsigned integer (32-bit)
 +
((d0 << 24) + (d1 << 16) + (d2 << 8) + d3)-((d0 >> 7)*4294967296)) // signed integer (32-bit) Two's complement
 +
 +
256 = (1 << 8)
 +
65536 = (1 << 16)
 +
16777216 = (1 << 24)
 +
4294967296 = (1 << 32)
 +
 +
==== MIA >> Monitor = MIAtor ====
 +
* parts:
 +
** Arduino UNO R3 (or CH340 clone EUR 6,49)
 +
** MCP2515 / TJA1050 shield http://blog.dimitarmk.com/wp-content/uploads/2016/12/wiringarduinomcp2515.png (8MHz EUR 4,79)
 +
** OBD-II connector: Pin-6=CAN-high / Pin-14=CAN-low EUR 1,69
 +
** 20x4 LCD display plus I2C EUR 8,77
 +
* libaries:
 +
** https://github.com/marcoschwartz/LiquidCrystal_I2C
 +
** https://github.com/coryjfowler/MCP_CAN_lib (clockset to MCP_8MHz at mcp_can.h line 98)
 +
* code:
 +
** based on work of Voltix @ https://miahammia.wordpress.com/2017/10/08/infobox/
 +
<pre>
 +
// MIA >> Monitor = MIAtor
 +
// all about @ https://bastelbude.grade.de/mediawiki/index.php?title=MIA_electric#MIA_.3E.3E_Monitor_.3D_MIAtor
 +
// based on Voltix's work @ https://miahammia.wordpress.com/2017/10/08/infobox/
 +
 +
// CANbus
 +
#include <mcp_can.h>                  // https://github.com/coryjfowler/MCP_CAN_lib (clockset to MCP_8MHz at mcp_can.h line 98)
 +
#include <SPI.h>
 +
 +
// LCD
 +
#include <Wire.h>
 +
#include <LiquidCrystal_I2C.h>        // https://github.com/marcoschwartz/LiquidCrystal_I2C
 +
LiquidCrystal_I2C lcd(0x3F,20,4);    // set the LCD address to 0x3F for a 20 chars and 4 line display
 +
 +
long unsigned int rxId;
 +
unsigned char len = 0;
 +
unsigned char rxBuf[8];
 +
float Volts;
 +
float Amps;
 +
float Celsius;
 +
int SOC;
 +
int SOH;
 +
String Status;
 +
String Emergency;
 +
String Regeneration;
 +
float ChargeCurrent;
 +
float ChargeVoltage;
 +
char myBuf[8];
 +
String LCDline[4];
 +
 +
MCP_CAN CAN0(10);                              // Set CS to pin 10
 +
 +
 +
void myPrint(){
 +
  Serial.println(LCDline[0]);
 +
  Serial.println(LCDline[1]);
 +
  Serial.println(LCDline[2]);
 +
  Serial.println(LCDline[3]);
 +
 +
  lcd.setCursor(0,0);
 +
  lcd.print(LCDline[0]);
 +
  lcd.setCursor(0,1);
 +
  lcd.print(LCDline[1]);
 +
  lcd.setCursor(0,2);
 +
  lcd.print(LCDline[2]);
 +
  lcd.setCursor(0,3);
 +
  lcd.print(LCDline[3]);
 +
 +
  delay(1000);                    // 1 second
 +
  }
 +
 +
void setup()
 +
{
 +
  lcd.init();                      // initialize the lcd
 +
  lcd.init();
 +
  // Print a message to the LCD.
 +
  lcd.backlight();
 +
  LCDline[0] = "  Hello world!";
 +
  LCDline[1] = "MIA>>Monitor=MIAtor";
 +
  LCDline[2] = "bastelbude.grade.de";
 +
  LCDline[3] = "  ver. 2017-12-21";
 +
 +
  Serial.begin(115200);
 +
  CAN0.begin(CAN_500KBPS);                      // init can bus : baudrate = 500k
 +
  pinMode(2, INPUT);                            // Setting pin 2 for /INT input
 +
 +
 +
  Serial.println("MCP2515 Library Receive Example...");
 +
  //myPrint();
 +
 +
}
 +
 +
void loop()
 +
{
 +
    if(!digitalRead(2))                          // If pin 2 is low, read receive buffer
 +
    {
 +
      CAN0.readMsgBuf(&len, rxBuf);              // Read data: len = data length, rxBuf = data byte(s)
 +
      rxId = CAN0.getCanId();                    // Get message ID
 +
 +
      if (rxId == 0x620)                                // battery related messageID 620
 +
        {
 +
        LCDline[0] = "Bat: ";
 +
     
 +
        Volts = ((float)(rxBuf[2]*256+rxBuf[3]))/100;  // Voltage with decimals
 +
        Amps = ((float)(rxBuf[0]*256+rxBuf[1]))/10;    // current drawn or regenerated, allow negative
 +
        Celsius = ((float)rxBuf[4]);                    // Temperature, allow negative
 +
        SOC = ((int)rxBuf[5]);                          // State Of Charge
 +
 +
        LCDline[0] =  dtostrf(Volts,4,1,myBuf);        //set first line
 +
        LCDline[0] += "V | ";
 +
        LCDline[0] += dtostrf(Amps,6,1,myBuf);        //length of string=6 decimal places=1
 +
        LCDline[0] += "A |";
 +
        LCDline[0] += dtostrf(Celsius,2,0,myBuf);      //length of string=2 decimal places=0
 +
        LCDline[0] += "C";
 +
 +
        switch (rxBuf[6]&0x07) {                      //mask lowest 3 bits (48+49+50) = status
 +
          case 0:     
 +
            Status = "Ready    | ";
 +
            break;
 +
          case 1:     
 +
            Status = "Run      | ";
 +
            break;
 +
          case 2:     
 +
            Status = "Downgrad.| ";
 +
            break;
 +
          case 3:     
 +
          Status = "Charge    | ";
 +
            break;
 +
          case 4:     
 +
            Status = "Error    | ";
 +
            break;
 +
          case 5:     
 +
            Status = "Init    | ";
 +
            break;
 +
          case 6:     
 +
            Status = "Stop    | ";
 +
            break;
 +
        }
 +
 +
        if ((rxBuf[6]&0x40)== 0)                        // bit 54 Emergency
 +
          {
 +
          Emergency = "noEmergcy";             
 +
          } else {
 +
          Emergency = "Emergency";               
 +
          }
 +
 +
        if ((rxBuf[6]>>7)== 1)                        // bit 55 Regeneration
 +
          {
 +
          Regeneration = "okRegen | ";         
 +
          } else {
 +
          Regeneration = "noRegen | ";     
 +
          }
 +
       
 +
        SOH = ((int)rxBuf[7]);                          // State Of Health
 +
 +
        LCDline[1] =  Status;                          //set second line
 +
        LCDline[1] += Emergency;
 +
                       
 +
        LCDline[2] =  Regeneration;                    // set third line
 +
        LCDline[2] += "H=";
 +
        LCDline[2] += SOH;
 +
        LCDline[2] += " C=";
 +
        LCDline[2] += SOC;
 +
        LCDline[2] += "%";
 +
     
 +
        Serial.println();                        // new line
 +
 +
        Serial.print("ID 620 raw data: ");
 +
        for(int i = 0; i<len; i++)                // Print each byte of the data
 +
          {
 +
          if(rxBuf[i] < 0x10)                    // If data byte is less than 0x10, add a leading zero
 +
            {
 +
            Serial.print("0");
 +
            }
 +
            Serial.print(rxBuf[i], HEX);
 +
            Serial.print(" ");
 +
            }
 +
        Serial.println();
 +
       
 +
        LCDline[3] = "";                              // set fourth line
 +
        for(int i = 0; i<len; i++)                    // Print each byte of the data
 +
          {
 +
          if(rxBuf[i] < 0x10)                          // If data byte is less than 0x10, add a leading zero
 +
            {
 +
            LCDline[3] += "0";
 +
            }
 +
            sprintf(myBuf,"%hhX",rxBuf[i]);
 +
            LCDline[3] += myBuf;
 +
          }
 +
       
 +
        myPrint();                                  // lcd-print and serial-print of all four lines
 +
    }
 +
 +
       
 +
 
 +
    if (rxId == 0x621)                                // BMS error messageID 621
 +
        {
 +
        Serial.print("ID 621 raw data: ");
 +
        for(int i = 0; i<len; i++)                    // Print each byte of the data
 +
          {
 +
          if(rxBuf[i] < 0x10)                        // If data byte is less than 0x10, add a leading zero
 +
            {
 +
            Serial.print("0");
 +
            }
 +
            Serial.print(rxBuf[i], HEX);
 +
            Serial.print(" ");
 +
            }
 +
        Serial.println();
 +
        }
 +
   
 +
    if (rxId == 0x622)                                        // BMS > Charger messageID 622
 +
        {
 +
        ChargeCurrent = ((float)(rxBuf[0]*256+rxBuf[1]))/10;  // Amps with decimals
 +
        ChargeVoltage = ((float)(rxBuf[3]*256+rxBuf[4]))/100;  // Voltage with decimals
 +
 +
        Serial.print("ID 622 raw data: ");
 +
        for(int i = 0; i<len; i++)                    // Print each byte of the data
 +
          {
 +
          if(rxBuf[i] < 0x10)                        // If data byte is less than 0x10, add a leading zero
 +
            {
 +
            Serial.print("0");
 +
            }
 +
            Serial.print(rxBuf[i], HEX);
 +
            Serial.print(" ");
 +
            }
 +
        Serial.println();
 +
        }   
 +
    }
 +
 +
}
 +
</pre>
 +
 
=== DC charging ===
 
=== DC charging ===
 
==== CCS ====
 
==== CCS ====
Line 33: Line 314:
 
* docs
 
* docs
 
** http://tesla.o.auroraobjects.eu/Design_Guide_Combined_Charging_System_V3_1_1.pdf
 
** http://tesla.o.auroraobjects.eu/Design_Guide_Combined_Charging_System_V3_1_1.pdf
 +
 +
== spare + replacement parts ==
 +
* rear shocks
 +
** https://www.merlinmotorsport.co.uk/p/avo-coil-over-shock-absorber-with-poly-bush-mount-for-1-9-inch-springs-pa
 +
* rims
 +
** 3x98mm bolt-pattern
 +
 
[[category:Projekte]]
 
[[category:Projekte]]

Latest revision as of 17:21, 26 August 2019

sandbox

CAN-bus sniffing

socketcand ('can over tcp/ip')

slcand -o -s6 -t hw 115200 /dev/ttyusb0
ip link set up slcan0
socketcand -i slcan0

CANcool

'Berechnungs-Term'

  • operators:
+  // addition
-  // subtraction
*  // multiplication
/  // division
<< // Bit shift left
>> // Bit shift right
&  // AND
|  // OR
~  // XOR
  • variables:
d0 1st byte (decimal)
d1 2nd byte (decimal)
d3 3rd byte (decimal)
d4 ... 
d5 ...
d6 ...
d7 ...
  • samples:
d0                                                                 // unsigned char (8-bit)
(d0 - ((d0 >> 7)*256))                                             // signed char (8-bit) Two's complement
((d0 << 8) + d1) ^= MSB * 256 + LSB                                // unsigned short (16-bit)
(((d0 << 8) + d1) - ((d0 >> 7)*65536))                             // signed short (16-bit) Two's complement
((d0 << 24) + (d1 << 16) + (d2 << 8) + d3)                         // unsigned integer (32-bit)
((d0 << 24) + (d1 << 16) + (d2 << 8) + d3)-((d0 >> 7)*4294967296)) // signed integer (32-bit) Two's complement

256 = (1 << 8)
65536 = (1 << 16)
16777216 = (1 << 24)
4294967296 = (1 << 32)

MIA >> Monitor = MIAtor

// MIA >> Monitor = MIAtor
// all about @ https://bastelbude.grade.de/mediawiki/index.php?title=MIA_electric#MIA_.3E.3E_Monitor_.3D_MIAtor
// based on Voltix's work @ https://miahammia.wordpress.com/2017/10/08/infobox/

// CANbus
#include <mcp_can.h>                   // https://github.com/coryjfowler/MCP_CAN_lib (clockset to MCP_8MHz at mcp_can.h line 98)
#include <SPI.h>

// LCD 
#include <Wire.h> 
#include <LiquidCrystal_I2C.h>        // https://github.com/marcoschwartz/LiquidCrystal_I2C 
LiquidCrystal_I2C lcd(0x3F,20,4);     // set the LCD address to 0x3F for a 20 chars and 4 line display

long unsigned int rxId;
unsigned char len = 0;
unsigned char rxBuf[8];
float Volts;
float Amps;
float Celsius;
int SOC;
int SOH;
String Status;
String Emergency;
String Regeneration;
float ChargeCurrent;
float ChargeVoltage;
char myBuf[8];
String LCDline[4];

MCP_CAN CAN0(10);                               // Set CS to pin 10


void myPrint(){
  Serial.println(LCDline[0]);
  Serial.println(LCDline[1]);
  Serial.println(LCDline[2]);
  Serial.println(LCDline[3]);

  lcd.setCursor(0,0); 
  lcd.print(LCDline[0]);
  lcd.setCursor(0,1);
  lcd.print(LCDline[1]);
  lcd.setCursor(0,2);
  lcd.print(LCDline[2]);
  lcd.setCursor(0,3);
  lcd.print(LCDline[3]);

  delay(1000);                     // 1 second
  }

void setup()
{
  lcd.init();                      // initialize the lcd 
  lcd.init();
  // Print a message to the LCD.
  lcd.backlight();
  LCDline[0] = "  Hello world!";
  LCDline[1] = "MIA>>Monitor=MIAtor";
  LCDline[2] = "bastelbude.grade.de";
  LCDline[3] = "  ver. 2017-12-21";

  Serial.begin(115200);
  CAN0.begin(CAN_500KBPS);                       // init can bus : baudrate = 500k 
  pinMode(2, INPUT);                            // Setting pin 2 for /INT input


  Serial.println("MCP2515 Library Receive Example...");
  //myPrint();

}

void loop()
{
    if(!digitalRead(2))                          // If pin 2 is low, read receive buffer
    {
      CAN0.readMsgBuf(&len, rxBuf);              // Read data: len = data length, rxBuf = data byte(s)
      rxId = CAN0.getCanId();                    // Get message ID

      if (rxId == 0x620)                                // battery related messageID 620
        {
        LCDline[0] = "Bat: ";
       
        Volts = ((float)(rxBuf[2]*256+rxBuf[3]))/100;   // Voltage with decimals
        Amps = ((float)(rxBuf[0]*256+rxBuf[1]))/10;     // current drawn or regenerated, allow negative
        Celsius = ((float)rxBuf[4]);                    // Temperature, allow negative
        SOC = ((int)rxBuf[5]);                          // State Of Charge

        LCDline[0] =  dtostrf(Volts,4,1,myBuf);        //set first line
        LCDline[0] += "V | ";
        LCDline[0] += dtostrf(Amps,6,1,myBuf);         //length of string=6 decimal places=1
        LCDline[0] += "A |";
        LCDline[0] += dtostrf(Celsius,2,0,myBuf);      //length of string=2 decimal places=0
        LCDline[0] += "C";

        switch (rxBuf[6]&0x07) {                       //mask lowest 3 bits (48+49+50) = status
          case 0:      
            Status = "Ready    | ";
            break;
          case 1:      
            Status = "Run      | ";
            break;
          case 2:      
            Status = "Downgrad.| ";
            break;
          case 3:      
           Status = "Charge    | ";
            break;
          case 4:       
            Status = "Error    | ";
            break;
          case 5:       
            Status = "Init     | ";
            break;
          case 6:       
            Status = "Stop     | ";
            break;
        }

        if ((rxBuf[6]&0x40)== 0)                         // bit 54 Emergency
          {
          Emergency = "noEmergcy";              
          } else {
          Emergency = "Emergency";                 
          }

        if ((rxBuf[6]>>7)== 1)                         // bit 55 Regeneration
          {
          Regeneration = "okRegen | ";           
          } else {
          Regeneration = "noRegen | ";       
          }
        
        SOH = ((int)rxBuf[7]);                          // State Of Health

        LCDline[1] =  Status;                           //set second line
        LCDline[1] += Emergency;
                        
        LCDline[2] =  Regeneration;                     // set third line
        LCDline[2] += "H=";
        LCDline[2] += SOH;
        LCDline[2] += " C=";
        LCDline[2] += SOC;
        LCDline[2] += "%";
       
        Serial.println();                         // new line

        Serial.print("ID 620 raw data: ");
        for(int i = 0; i<len; i++)                // Print each byte of the data
          {
          if(rxBuf[i] < 0x10)                     // If data byte is less than 0x10, add a leading zero
            {
            Serial.print("0");
            }
            Serial.print(rxBuf[i], HEX);
            Serial.print(" ");
            }
        Serial.println();
        
        LCDline[3] = "";                               // set fourth line
        for(int i = 0; i<len; i++)                     // Print each byte of the data
          {
          if(rxBuf[i] < 0x10)                          // If data byte is less than 0x10, add a leading zero
            {
            LCDline[3] += "0";
            }
            sprintf(myBuf,"%hhX",rxBuf[i]);
            LCDline[3] += myBuf;
          }
        
        myPrint();                                   // lcd-print and serial-print of all four lines
    } 

        
   
    if (rxId == 0x621)                                // BMS error messageID 621
        {
        Serial.print("ID 621 raw data: ");
        for(int i = 0; i<len; i++)                    // Print each byte of the data
          {
          if(rxBuf[i] < 0x10)                         // If data byte is less than 0x10, add a leading zero
            {
            Serial.print("0");
            }
            Serial.print(rxBuf[i], HEX);
            Serial.print(" ");
            }
        Serial.println();
        } 
    
    if (rxId == 0x622)                                        // BMS > Charger messageID 622
        {
        ChargeCurrent = ((float)(rxBuf[0]*256+rxBuf[1]))/10;  // Amps with decimals
        ChargeVoltage = ((float)(rxBuf[3]*256+rxBuf[4]))/100;  // Voltage with decimals

        Serial.print("ID 622 raw data: ");
        for(int i = 0; i<len; i++)                    // Print each byte of the data
          {
          if(rxBuf[i] < 0x10)                         // If data byte is less than 0x10, add a leading zero
            {
            Serial.print("0");
            }
            Serial.print(rxBuf[i], HEX);
            Serial.print(" ");
            }
        Serial.println();
        }    
    }

}

DC charging

CCS

  • parts
    • CCS-socket e.g. Phoenix Contact ~EUR 800,-
    • input voltage monitor
    • power contactor (+125A disconnecting device) Tyco ~EUR 150,-
    • current monitor
    • V2G in-vehicle-charge-controller e.g. EVAcharge SE ~EUR 750,-
      • ARM microcontroller
      • Linux OS
      • fully programmable
      • PWM duty cycle detection (CP low level communication)
      • switchable resistors (CP low level communication)
      • HomePlug Green PHY integration (PLC high level communication)
      • Proximity pilot signal input (PP)
      • lock-motor output
      • lock-motor end switch input
      • lock-motor fault pin
      • CAN transceiver (BMS communication)
      • 6 GPIOs (current-monitoring?, voltage-monitoring?, temprature-monitoring?, power contactor-driver?, (contactor-monitoring?))

spare + replacement parts