RPiAIS

stretch

• get http://www.aishub.net/rpiais
  • enable SSH permanently
• check http://192.168.1.100:8080
• set configuration
  • input UDP Server
  • host 127.0.0.1
  • port 5001
• start dispatcher

setup

• connect via ssh or scp as pi

sudo apt-get update
sudo apt-get upgrade
sudo su
mc

• enable root login over SSH
  • add to /etc/ssh/sshd_config

    PermitRootLogin yes

  • restart service

    sudo /etc/init.d/ssh restart

  • set root password

    sudo passwd root

• set up static IP at /etc/dhcpcd.conf

interface eth0
static ip_address=192.168.1.110/24
static routers=192.168.1.1
static domain_name_servers=192.168.1.1

• reboot

install

rtl-sdr use apt-get install rtl-sdr instead

• connect via ssh or scp as pi

sudo su -
apt-get update
apt-get install git
git clone git://git.osmocom.org/rtl-sdr.git
apt-get install libusb-dev libusb-1.0 libtool cmake
apt-get install build-essential
 
cd rtl-sdr/
mkdir build
cd build
cmake ../
make
make install
ldconfig
 
cd ..
cp rtl-sdr.rules /etc/udev/rules.d/

• Blacklist the kernel module dvb_usb_rtl28xxu by adding the line blacklist dvb_usb_rtl28xxu to /etc/modprobe.d/blacklist-dvb_usb_rtl28xxu.conf
• reboot
• Test the installation:
  • rtl_test -t
  • output:

Found 1 device(s):
  0:  Realtek, RTL2838UHIDIR, SN: 00000001

Using device 0: Terratec Cinergy T Stick RC (Rev.3)
Found Elonics E4000 tuner
Supported gain values (14): -1.0 1.5 4.0 6.5 9.0 11.5 14.0 16.5 19.0 21.5 24.0 29.0 34.0 42.0
Sampling at 2048000 S/s.
Benchmarking E4000 PLL...
[E4K] PLL not locked for 51000000 Hz!
[E4K] PLL not locked for 2187000000 Hz!
[E4K] PLL not locked for 1094000000 Hz!
[E4K] PLL not locked for 1243000000 Hz!
E4K range: 52 to 2186 MHz
E4K L-band gap: 1094 to 1243 MHz

rtl-ais

apt-get update
apt-get install rtl-sdr librtlsdr-dev libusb-1.0-0-dev
git clone https://github.com/dgiardini/rtl-ais
cd rtl-ais
make
cp rtl_ais /usr/local/bin/

• add /etc/systemd/system/ais.service

[Unit]
Description=AIS
After=syslog.target network-online.target

[Service]
Type=simple
User=root
ExecStart=/usr/local/bin/rtl_ais -p 28 -P 5001
Restart=on-failure
RestartSec=10
KillMode=process

[Install]
WantedBy=multi-user.target

• systemctl daemon-reload
• systemctl enable ais
• systemctl start ais
• systemctl stop ais

aisdeco

• http://xdeco.org/?page_id=30#ai2
• https://github.com/xginn8/aisdeco
• https://www.wiganpi.co.uk/how-to-install-acarsdeco2-on-pi2-or-pi3-running-raspbian-stretch-and-dump1090/
• ...