Difference between revisions of "MIA electric"
(→CAN sniffing) |
|||
| Line 7: | Line 7: | ||
** OBD-II connector: Pin-6=CAN-high / Pin-14=CAN-low | ** OBD-II connector: Pin-6=CAN-high / Pin-14=CAN-low | ||
** CANcool https://github.com/MHS-Elektronik/CANcool | ** CANcool https://github.com/MHS-Elektronik/CANcool | ||
| + | |||
| + | === CANcool === | ||
| + | * [http://www.mhs-elektronik.de/index.php?module=content&action=show&page=can_cool website] | ||
| + | * [https://www.mikrocontroller.net/topic/283166 forum] | ||
| + | * [https://github.com/MHS-Elektronik/CANcool sources] | ||
| + | ==== 'Berechnungs-Term' ==== | ||
| + | * operators: | ||
| + | << Bits shift left | ||
| + | >> Bits shift right | ||
| + | & AND | ||
| + | | OR | ||
| + | ~ XOR | ||
| + | * variables: | ||
| + | d0 1st byte (decimal) | ||
| + | d1 2nd byte (decimal) | ||
| + | d3 3rd byte (decimal) | ||
| + | d4 ... | ||
| + | d5 ... | ||
| + | d6 ... | ||
| + | d7 ... | ||
| + | * samples: | ||
| + | ((d0 << 8) + d1) ^= MSB * 256 + LSB //unsigned short (16-bit) | ||
| + | (((d0 << 8) + d1) - ((d0 >> 7)*65536)) //Signed short (16-bit) Two's complement | ||
| + | |||
=== DC charging === | === DC charging === | ||
Revision as of 16:16, 14 December 2017
Contents
sandbox
CAN-bus sniffing
- parts
- Arduino UNO R3 (or CH340 clone EUR 6,49)
- MCP2515 / TJA1050 shield
(8MHz EUR 4,79) - https://github.com/latonita/arduino-canbus-monitor (MCP_8MHz, CAN_500KBPS)
- OBD-II connector: Pin-6=CAN-high / Pin-14=CAN-low
- CANcool https://github.com/MHS-Elektronik/CANcool
CANcool
'Berechnungs-Term'
- operators:
<< Bits shift left >> Bits shift right & AND | OR ~ XOR
- variables:
d0 1st byte (decimal) d1 2nd byte (decimal) d3 3rd byte (decimal) d4 ... d5 ... d6 ... d7 ...
- samples:
((d0 << 8) + d1) ^= MSB * 256 + LSB //unsigned short (16-bit) (((d0 << 8) + d1) - ((d0 >> 7)*65536)) //Signed short (16-bit) Two's complement
DC charging
CCS
- prerequisites
- explore V2G protocol
- discover BMS <> Charger CANbus conversation
- BMS/Battery e4v.eu
- onboard charger ies-synergy.com
- develop BMS <> PCL communication
- parts
- CCS-socket e.g. Phoenix Contact ~EUR 800,-
- input voltage monitor
- power contactor (+125A disconnecting device) Tyco ~EUR 150,-
- current monitor
- V2G in-vehicle-charge-controller e.g. EVAcharge SE ~EUR 750,-
- ARM microcontroller
- Linux OS
- fully programmable
- PWM duty cycle detection (CP low level communication)
- switchable resistors (CP low level communication)
- HomePlug Green PHY integration (PLC high level communication)
- Proximity pilot signal input (PP)
- lock-motor output
- lock-motor end switch input
- lock-motor fault pin
- CAN transceiver (BMS communication)
- 6 GPIOs (current-monitoring?, voltage-monitoring?, temprature-monitoring?, power contactor-driver?, (contactor-monitoring?))
